New 2024 NACE-CIP1-001 exam questions Welcome to download the newest Pass4training NACE-CIP1-001 PDF dumps (100 Q&As)
P.S. Free 2024 CIP Level 1 NACE-CIP1-001 dumps are available on Google Drive shared by Pass4training
NEW QUESTION # 41
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Application Guidelines
- C. Technical Data Sheet
- D. Safety Data Sheet;
Answer: C
NEW QUESTION # 42
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record the segment with the less aggressive profile
- C. Record your result by identifying two segments
- D. Record the segment with the more aggressive profile
Answer: B
NEW QUESTION # 43
A magnetic pull-off type gauge is a good choice when:
- A. Accuracy is not required
- B. Performing an adhesion test
- C. When working on non-ferrous metals
- D. When an intrinsically safe tool is required
Answer: D
NEW QUESTION # 44
To achieve consistently accurate results with ALL alt test equipment
- A. avoid placing the sample discs on a surface.
- B. wash your hands before sampling.
- C. wear gloves when sampling.
- D. calibrate the instrument in the field.
Answer: B
NEW QUESTION # 45
SSPC SP 1 identifies the use of:
- A. Biodegradable detergents
- B. A wide variety of materials
- C. Inorganic solvents
- D. Organic solvents
Answer: B
NEW QUESTION # 46
ASTM Standards are applicable:
- A. In North America
- B. In Asia
- C. In the USA
- D. When specified
Answer: D
NEW QUESTION # 47
Whenever dissimilar metals must join, the most common practice is to
- A. provide cathodic protection to prevent corrosion,
- B. avoid coating all connected dissimilar metals.
- C. coat all connected dissimilar metals.
- D. provide anodic protection to prevent corrosion.
Answer: C
NEW QUESTION # 48
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Measuring ditty, tacky, or soft films
- B. Failing to determine the base metal reading (BMR)
- C. Rotating the dial too fast when taking measurements
- D. Taking measurements too far from the edge of a surface
Answer: A,B,C
NEW QUESTION # 49
Check abrasive blast pressure close to the
- A. blast nozzle
- B. blast pot
- C. substrate
- D. compressor
Answer: A
NEW QUESTION # 50
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Check the PPE used by the Applicators
- C. Assume the role of the Safety Inspector
- D. Act in accordance with the site safety requirements and set an example
Answer: D
NEW QUESTION # 51
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: A
NEW QUESTION # 52
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Ultra-Violet light may contaminant the surface
- C. Synthetic oil or grease may not be identified
- D. Presence of weld spatter may produce a false positive
Answer: C
NEW QUESTION # 53
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. No comments regarding the application team
- C. Objective comments regarding the application work
- D. Subjective comments re ding the application team
Answer: B
NEW QUESTION # 54
Which of these tests uses a syringe?
- A. Sleeve test
- B. Soluble salts meter
- C. Potassium ferricyanide
- D. Bresle patch
Answer: D
NEW QUESTION # 55
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Edges and corners
- C. Complex geometric shapes
- D. Welds
Answer: A
NEW QUESTION # 56
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. Inspectors rarely change on a project.
- C. the information impacts future projects.
- D. The information aids communication with supervisors.
Answer: A,C,D
NEW QUESTION # 57
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. It depends on which hand tool the Contractor selects
- C. It depends on which power tool the Contractor selects
- D. No, because there is no real difference in the standards
Answer: D
NEW QUESTION # 58
Which is a component that supplies most of the features and functions of the material?
- A. pigment
- B. binder
- C. solvent
- D. additive
Answer: B
NEW QUESTION # 59
The most important factor resulting in improved job site safety is:
- A. Safety Enforcement
- B. Engineering Controls
- C. Personal Protective Equipment
- D. Situational Awareness
Answer: D
NEW QUESTION # 60
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- B. SSPC PA 2
- C. NACE SP 0188
- D. NACE SP 0178
Answer: A
NEW QUESTION # 61
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. All personnel involved in the job
- C. The Owner's personnel
- D. The Application personnel
Answer: B
NEW QUESTION # 62
......
NACE-CIP1-001 exam questions from Pass4training dumps: https://examsboost.pass4training.com/NACE-CIP1-001-test-questions.html (100 Q&As)
